Skip to content
KORNDEX – Home

Abrasives · 2 min read

Cleaning clogged sandpaper – is it worth it?

Knocking out, blowing out, using a cleaning stick or rinsing: what helps with clogged sandpaper – and when only a new disc will do.

Last updated:

KORNDEX sells abrasives – matching products are linked below the article.

KORNDEX sanding discs, P240 sanding roll and sanding sheets on the workbench

Why sandpaper clogs

Sandpaper is clogged when the debris lodges between the grains. It happens fastest with soft, warm material: fresh paint, resinous softwood, primer surfacer, body filler, plastic. If the disc gets hot, the dust melts on and forms small, hard lumps.

The grain underneath is often still sharp – it just cannot reach the surface any more.

How to clean it

Loose dust: knock out the disc or sheet, blow compressed air against the abrasive side, or run it over a clean brush with the extraction on.

Stuck dust: a rubber cleaning stick – basically a large eraser – is held against the running abrasive and pulls the debris out of the grain. That works on the random orbital sander, on the belt sander and by hand on a clamped sheet.

Rinse wet sanding paper and non-woven pads under water and let them dry, or carry on sanding wet straight away.

When cleaning no longer helps

Melted lumps of paint and resin hardly come out again – and they are exactly what drags deep scratches. If the disc is covered in them, change it. Blunt grain does not come back by cleaning either: if the disc only glides, gets warm and removes nothing although it is clean, it is worn out.

Rule of thumb: cleaning is worth it for coarse and medium paper on wood when only dust is stuck in it. For fine grits on paint, a fresh disc is cheaper than reworking a scratch.

Better to prevent it

Sand with extraction and choose a matching hole pattern and pad so the dust gets away. Light pressure: pressure makes the disc hot, and heat makes the dust melt on. Let paint and primer surfacer cure fully before you sand.

On primer surfacer and body filler a mesh disc (PRO NET) hardly clogs, because the dust passes through everywhere. Paper with an open coat and a stearate coating stays open longer on paint and wood.

FAQ

Can sandpaper be reused?

Yes, as long as the grain is sharp. A half-used hook-and-loop disc can be taken off and used again later if it is clean and free of lumps. Worn-out grain does not cut any more, however clean it is.

Can I wash out clogged sandpaper?

Only waterproof wet sanding paper, mesh and non-woven pads. Ordinary paper softens, the grain comes off, and the disc no longer holds on the hook and loop.

Terms in this article

All terms in the sanding glossary →

More on this topic

Matching products

  • KORNDEX

    PRO NET 150

    Mesh sanding disc Ø 150 mm – virtually dust-free, sands for longer.

    €24.90

    €0.50 / pc · incl. VAT, plus shipping

  • KORNDEX

    PRO CUT 150

    Professional sanding disc Ø 150 mm – maximum stock removal.

    €24.90

    €0.50 / pc · incl. VAT, plus shipping

  • KORNDEX sanding discs, P240 sanding roll and sanding sheets on the workbench

    Abrasives

    When is a sanding disc worn out?

    It stops biting, gets hot, leaves scratches: four signs the disc has to come off – and how to make it last longer.

    Read · 1 min
  • Sanding discs, sheets, a roll and sanding sponges next to a painted panel, wood, steel and plastic

    Abrasives

    Mesh sanding discs vs. regular sandpaper

    Mesh extracts dust across its whole surface and does not clog; paper is cheaper and cuts harder. When to use which.

    Read · 2 min
  • KORNDEX sanding discs, P240 sanding roll and sanding sheets on the workbench

    Abrasives

    How to store sandpaper properly

    Moisture and heat make sandpaper curl and age the bond. Keep it dry, flat and in its packaging – and here’s why curled paper sands worse.

    Read · 1 min