Skip to content
KORNDEX – Home
Random orbital sander on a plastic bumper

Properly prepared.

Sanding plastic: grits and work steps

Key plastic bumpers and trim ready for paint, or fine-sand them – with light pressure. For painters, body shop pros and anyone refinishing add-on parts themselves.

Short answer: For plastic: from P180 to P1000, step by step – P180 → P240 → P320 → P400 → P600 → P800 → P1000. How far depends on the goal: for painting up to P400, with fine sanding up to P1000. Skip no step – each one removes the scratches of the one before.

3 work stepsGrit P180 to P1000Finish set for high gloss €59.90

The film

Sanding for plastic

Prepare bumpers and trim cleanly – with light pressure for optimum adhesion.

Find the right abrasives

Which sandpaper for plastic?

3 stages from coarse to fine – and where you start depending on the condition of the surface.

From raw to finished

  1. Plastic bumper being scuff-sanded with a random orbital sander

    Stage 1: Remove scratches

    P180 – P320

  2. Fine sanding a bumper by hand with a foam sanding pad

    Stage 2: Key for painting

    P320 – P400

  3. Finely and evenly sanded bumper

    Stage 3: Fine sanding without paint

    P600 – P1000

The whole grit sequence

Work steps

3 steps in working order – from coarse to fine. For each step, the grits and the matching product.

  1. 1

    Remove scratches and burrsDry

    Smooth mould flash and deep scratches with P180, then work out the marks with P240 and P320. Plastic rarely needs anything coarser than P180.

    Move on when: No burrs and no deep scratches left – under raking light only the even P320 scratch pattern.

    For thisPRO FILM 150 P240from €15.90
  2. 2

    Paint preparationDry

    Key the whole surface with P320 to P400 until nothing shines any more. Then clean it and apply adhesion promoter.

    Move on when: The surface is evenly matt everywhere – no glossy spot left, not even on edges and swage lines.

    Tip: Edges and swage lines with non-woven abrasive instead of a disc – that way you won't sand through there. In the system: Key paint & plastic →

    For thisPRO FILM 150 P320from €15.90
    For edges and swage linesPRO FLEECEfrom €14.90
  3. 3

    Fine sanding without paintDry, fine grits wet

    For visible parts that won't be painted: fine and even with a film disc or foam pad, ideally wet – without heat.

    Move on when: Wiped damp, an even, fine scratch pattern with no stray scratches – then polish.

    For thisPRO FILM 150 P600from €15.90

Dashed grits belong to the work step but are not yet in the range for Plastic – the link explains what the grit does.

The whole sequence at once

3 grits, 1 × smallest pack each: PRO FILM 150 (10 pcs) P240 · P320 · P400. We don’t stock P180 for this yet.

Or as a set: Finish set for high gloss (P1000–P2000) for €59.90 →

incl. VAT, plus shipping

All sets with complete grit sequences →

Matching products

7 products for Plastic – recommended ones first, each card starts with the grit you need first here.

Abrasives

  • PRO FLEECE

    KORNDEX
    152 × 229 mm
    Dimensions
    10 pcs
    Contents
    very fine (grey)
    Type
    €14.90

    €1.49 / pc · incl. VAT, plus shipping

  • PRO FILM 150

    P240KORNDEX
    Bestseller
    P240–P1500
    Grit
    150 mm
    Diameter
    10 pcs
    Contents
    €15.90

    €1.59 / pc · incl. VAT, plus shipping

  • SOFT FINISH

    P400KORNDEX
    Bestseller
    P400–P2000
    Grit
    150 mm
    Diameter
    10 pcs
    Contents
    €14.90

    €1.49 / pc · incl. VAT, plus shipping

  • PRO SHEET 230 × 280 wet

    P400KORNDEX
    P400–P2000
    Grit
    230 × 280 mm
    Dimensions
    25 pcs
    Contents
    €19.90

    €0.80 / pc · incl. VAT, plus shipping

Accessories · Machines · Sets & bundles

  • Masking tape 110 °C

    KORNDEX
    25 mm
    Width
    €5.90

    €0.12 / m · incl. VAT, plus shipping

  • KORNDEX EX 150

    KORNDEX EX 150 with extraction hose on the workbench, with P120, P240 and P400 sanding discs in front
    New
    150 mm
    Diameter
    €149.00

    incl. VAT, plus shipping

  • Finish set for high gloss

    KORNDEXFINISH SETKORNDEX
    P1000–P2000
    Grit
    30 discs, 25 sheets
    Contents
    €59.90

    incl. VAT, plus shipping

What matters with Plastic

What counts beyond the grit – technique, typical defects and the related guides.

Tips from the workshop

  • 01

    Clean first

    New parts carry release agent from the mould. Wipe them with plastic cleaner before the first sanding – otherwise the abrasive just rubs it into the surface.

  • 02

    Low pressure, low speed

    Plastic conducts heat poorly: with a lot of pressure and high speed it softens, the grain clogs and it smears. Use a random orbital with a small orbit on a low setting, and change the disc more often.

  • 03

    Remove dust antistatically

    Plastic builds up static when sanded and holds on to the dust – blowing it off is not enough. Wipe with an antistatic cloth or antistatic cleaner before adhesion promoter and paint, otherwise every speck ends up in the paint.

  • 04

    Don't forget adhesion promoter

    After keying and cleaning, bare plastic needs adhesion promoter before primer or paint – otherwise the paint flakes off at the first stone chip.

Related guides · 6 articles

  • Random orbital sander on a plastic bumper

    What grit sandpaper for plastic? Preparing bumpers

    Bumpers and trim panels smear, warp and reject paint if you treat them like sheet metal. Grit, pressure and the steps that follow.

    P180 → P240 → P320 → P400

    Read · 2 min
  • Fine sanding plastic by hand with a foam sanding pad

    Restoring headlights: which grit?

    Wet sand from P800 to P2000, then polish – and seal afterwards, or the lens will be cloudy again after one summer.

    P800 → P1000 → P1500 → P2000

    Read · 1 min
  • Random orbital sander on the door of a black car

    Sanding GRP: boats, motorhomes, body parts

    Keying gelcoat, levelling repairs, refining before paint: the sequence from P80 to P600 – and why the dust must stay out of your lungs.

    P80 → P120 → P180 → P240 → P320 → P400 → P600

    Read · 1 min

FAQ on Plastic

How do I key plastic so the paint holds?

After cleaning, matt it evenly with P320 to P400, and hard-to-reach areas with non-woven abrasive. Then adhesion promoter for plastics, followed by primer or paint.

Which grit do I use on a bumper before painting?

Clean first, then smooth scratches and dents with P180 to P240 and key the whole bumper evenly with P320 to P400 – edges and swages with an abrasive pad. Only scuff factory-primed new parts with P400 or a pad. Wherever bare plastic is exposed, an adhesion promoter goes on before primer or paint.

Sanding and painting plastic →

Why does plastic smear when sanding?

Too much pressure or speed creates heat and the plastic softens. Sand at low speed, with light pressure and a fine grit – or wet, which keeps it cool.

Do I need to key new, factory-primed plastic parts?

Yes, lightly: matt the factory primer evenly with P400 or non-woven abrasive without sanding through it. Where it does break through, apply adhesion promoter there before primer or paint.

How do I sand yellowed plastic headlights?

Mask all round, then wet-sand in stages from P800 via P1000 and P1500 to P2000 – each stage until the scratch pattern of the previous one has gone. Then polish and protect with UV-resistant clear coat or a sealant, otherwise the lens soon yellows again.

How can I tell which plastic it is?

By the marking on the back, such as >PP<, >PP-EPDM< or >ABS<. Soft, flexible bumpers (PP, PP-EPDM) heat up quickly and fray – use especially light pressure and always adhesion promoter. Hard parts such as ABS sand more like paint.

How do I sand plastic before bonding?

Adhesive holds on a rough, clean surface: degrease first, then roughen evenly with P180 to P240 and remove the sanding dust thoroughly. After that, do not touch the bonding surface again.

Sanding before bonding →

Which sandpaper do I use for epoxy resin?

Only sand once the resin has fully cured – soft resin smears and clogs every disc. Level coarsely with P120 to P180, then finer in steps and from about P800 wet up to P2000, then polish. Use low speed and little pressure so the resin does not heat up.

Sanding and polishing epoxy resin →

How do I sand uPVC windows before painting?

Clean and degrease the frames thoroughly, then only scuff lightly – with a fine abrasive pad or P240 to P320 until the surface is evenly matt everywhere. Sanding deeper is not needed. Then remove the dust and use a primer approved for plastic.

Can I fill cracks and dings in a bumper?

Yes, but with flexible plastic filler – ordinary polyester filler is too hard and cracks as soon as the part flexes. Key the area with P180 first and apply adhesion promoter; once cured, shape it with P180 to P240 and feather the edges with P320.

More applications

Different surface, different process – each application with its own work steps and grits.

  • Clear coat being wet-sanded by hand with a foam sanding pad
    Car & paintPerfect surfaces – from repair to finishP80 – P3000
  • Random orbital sander with dust extraction removing the weathered surface of an oak board
    WoodFrom raw to perfect – for furniture, interiors and moreP40 – P320
  • Random orbital sander removing rust from a steel sheet
    MetalRemove rust, refine surfaces, protect for goodP40 – P400
  • Random orbital sander on fresh body filler on a wing
    Body fillerLevel fast – shape cleanly – prepare perfectlyP80 – P240
  • Random orbital sander on grey primer surfacer on a masked car body
    Primer coatFor an even, high-quality paint finishP320 – P600

Still unsure?

The abrasive finder asks about your machine and goal – the material is already set – and tells you the product and grit.

Find abrasives for Plastic →