Skip to content
KORNDEX – Home

Abrasives · 3 min read

What grit for drywall, plaster and filler?

Joint compound with P120 and P180, ridges on smooth plaster with P80 to P120 – never sand into the paper facing. And how to keep the dust down, by machine or by hand.

Last updated: · published

KORNDEX sells abrasives – matching products are linked below the article.

Short answer: the grit sequence

Sanding discs, sheets, a roll and sanding sponges next to a painted panel, wood, steel and plastic

Sanding gypsum, plasterboard and plaster: which grit?

Joint compound on drywall seams is soft: P120 takes off ridges and trowel marks, P180 leaves the surface ready to paint. Going finer achieves nothing under wall paint – the paint covers the scratch pattern.

Only sand smooth plaster where ridges or filler residue stand proud, with P80 to P120. Textured and roughcast plaster are not sanded, otherwise the texture is gone. Firmly bonded wall paint needs no sanding before repainting; take off drips with P120.

Don’t sand into the paper facing

Plasterboard has a paper facing. If you sand through the filler into it, it roughens and the fibres stand up under the paint. So sand only the filler, with light pressure and held flat. If the paper does get roughened: prime and skim thinly, don’t keep sanding. Filling thinly means less sanding – and less chance of catching the paper.

Sandpaper that doesn’t clog

Gypsum dust is very fine and quickly clogs ordinary sandpaper – it then just glides over the surface. Abrasive mesh stays open because the dust is extracted through the weave; for the random orbital sander, mesh comes as a disc (PRO NET 150). By hand, use the hand sanding block with hook-and-loop strips: the long block bridges small hollows, and a vacuum on the extraction port takes the dust away directly.

Sanding walls: by hand or by machine?

For single seams, the hand block is enough. On large areas, a random orbital sander with extraction saves a lot of work: medium speed, set it down flat, guide it without pressure. If it tips onto its edge, it sands a hollow into the soft filler.

For whole rooms and ceilings there are long-reach drywall sanders (“giraffe” sanders) with a sanding head that is usually 225 mm. KORNDEX doesn’t stock these machines or their discs; if you fill only now and then, a random orbital sander and a hand block will do.

Sanding walls without dust

Entirely dust-free isn’t possible, but low-dust is: extraction on the machine or block, plus a vacuum of dust class L or M – gypsum dust quickly clogs a household vacuum’s filter and partly passes through it. Cover the floor, tape plastic sheeting over doors, ventilate. Whatever still rises is held back by an FFP2 mask.

Sanding drywall: grit and machine

In drywall work you sand joints and filled areas on plasterboard: P120 for ridges and edges, P180 for a paint-ready surface – finer brings nothing under wall paint. Mesh rather than paper, because gypsum dust clogs paper straight away.

Random orbital or orbital sander? For surfaces the random orbital sander with extraction and a mesh disc – faster and flatter. The orbital sander gets into corners and junctions, but removes less. For inside corners, usually only the hand block or a folded strip will do.

FAQ

How can I tell whether the wall is flat enough?

With raking light: hold a lamp flat against the wall. Ridges, dents and trowel marks then cast shadows you don’t notice in normal light – but they look exactly like that under the paint. Also feel the seams with the flat of your hand.

Do I need to prime filled areas before painting?

Yes. Filler absorbs differently from paper facing and plaster; without primer, seams and repairs show through the wall paint as matt or shiny patches. Sweep or vacuum off the sanding dust thoroughly first.

Can I wet sand joint compound?

Not with sandpaper. Small ridges on fresh filler can, however, be smoothed with a damp sponge – that creates no dust, but on larger areas it doesn’t replace sanding.

Can plaster be sanded – which grit?

Smooth lime or gypsum plaster, yes, in spots: take off ridges and filler residue with P80 to P120, flat and with light pressure. Not textured or rough-cast plaster, or the texture is gone. Cement render is hard and barely sands – better to knock it off than to sand it.

Terms in this article

All terms in the sanding glossary →

The whole sequence at once

3 grits, 1 × smallest pack each: PRO NET 150 (10 pcs) P80 · P120 · P180.

incl. VAT, plus shipping

In the range

More on this topic

Matching products

  • KORNDEX

    PRO NET 150

    Mesh sanding disc Ø 150 mm – virtually dust-free, sands for longer.

    €24.90

    €0.50 / pc · incl. VAT, plus shipping

  • KORNDEX

    Hand sanding block 70 × 198

    Hand sanding block with hook and loop and extraction port – for strips and rolls.

    €14.90

    incl. VAT, plus shipping

  • KORNDEX

    PRO STRIP 70 × 420

    Sanding strips 70 × 420 mm with hook and loop – for hand blocks and orbital sanders.

    €22.90

    €0.92 / pc · incl. VAT, plus shipping

  • KORNDEX EX 150 with extraction hose on the workbench, with P120, P240 and P400 sanding discs in front

    KORNDEX EX 150

    Random orbital sander 150 mm, 5 mm orbit, 350 W – the machine for our discs.

    €149.00

    incl. VAT, plus shipping

  • KORNDEX

    FFP2 dust mask

    Fold-flat FFP2 mask with valve – 10 pcs.

    €12.90

    incl. VAT, plus shipping

  • Random orbital sander on the door of a black car

    Sanders & technique

    Random orbital sander or orbital sander – which is better?

    The random orbital sander covers area, the orbital sander gets into corners. Motion, removal, abrasives and use compared – for wood, doors and drywall.

    Read · 3 min
  • KORNDEX sanding discs, P240 sanding roll and sanding sheets on the workbench

    Abrasives

    How to store sandpaper properly

    Moisture and heat make sandpaper curl and age the bond. Keep it dry, flat and in its packaging – and here’s why curled paper sands worse.

    Read · 1 min
  • Masked vehicle in the body shop

    Sanders & technique

    Sanding dust: extraction and masks

    Dust should be extracted before it ever reaches the air – and whatever still rises is caught by an FFP2 mask. Why this also makes your discs last longer.

    Read · 2 min