Skip to content
KORNDEX – Home

Car & paint · 1 min read

Repairing stone chips on a car: sanding the edge

Sand the edge with P400, remove rust down to bare metal, and after painting blend wet with P1500 and P2000 and polish.

Last updated:

KORNDEX sells abrasives – matching products are linked below the article.

Short answer: the grit sequence

Random orbital sander on a wing, sanding dust on the paint

First check how deep the chip is

If only the clear coat is damaged, wet sanding and polish are enough. If you can see primer or bare metal, the crater has to be filled and repainted. If rust shows, it has to go completely before anything else happens – otherwise it keeps growing under the paint.

Sand the edge, clean the crater

Clean and degrease the area and mask the surroundings. Carefully sand the edge of the crater with P400 so the edge tapers off softly and new paint adheres. Remove rust with a small sanding block or a sanding fleece until the metal is bright, and do not make the area bigger than necessary.

Fill, prime, smooth

Fill deep craters with fine filler or primer first. After it has cured, wet sand the primer flat with P600 until it is flush with the surroundings. Then apply colour and clear coat as specified by the manufacturer.

Blend and polish

Once the paint has cured, the repair usually stands slightly proud. Take down only that bump with P1500 wet, then blend the transition with P2000 and polish. Stay small: every extra centimetre is clear coat that is missing.

Typical mistakes

Painting over rust: it comes back through the paint.

Edge sanded too coarse: P180 and coarser leave scratches that show.

Area too big: sanding far around the chip means more paint and polish later.

FAQ

Which grit for a stone chip?

Sand the edge with P400, smooth the filled crater wet with P600, and after painting blend the transition wet with P1500 and P2000.

Does the rust in a stone chip have to go completely?

Yes – down to bare metal. Rust painted over keeps growing under the paint layer and comes through.

Terms in this article

All terms in the sanding glossary →

The whole sequence at once

4 grits, 1 × smallest pack each: PRO SHEET 230 × 280 wet (25 pcs) P400 · P600 · P1500 · P2000.

Or as a set: Finish set for high gloss (P1000–P2000) for €59.90 →

incl. VAT, plus shipping

More on this topic

Matching products

  • KORNDEX

    PRO SHEET 230 × 280 wet

    Waterproof sanding sheet 230 × 280 mm – for wet sanding paint.

    €19.90

    €0.80 / pc · incl. VAT, plus shipping

  • KORNDEX

    Hand sanding block 70 × 198

    Hand sanding block with hook and loop and extraction port – for strips and rolls.

    €14.90

    incl. VAT, plus shipping

  • KORNDEX

    PRO FLEECE

    Abrasive fleece 152 × 229 mm – matting, cleaning and scuffing without scratches.

    €14.90

    €1.49 / pc · incl. VAT, plus shipping

  • KORNDEXFINISH SETKORNDEX

    Finish set for high gloss

    For the finish before polishing – film, foam and wet sanding sheets.

    €59.90

    incl. VAT, plus shipping

  • KORNDEX

    Masking tape 110 °C

    Crepe tape for paintwork – leaves no residue, up to 110 °C, 50 m.

    €5.90

    €0.12 / m · incl. VAT, plus shipping

  • Wet sanding black paint with a foam sanding pad

    Car & paint

    Can you sand out scratches in car paint?

    Only scratches within the clear coat can be sanded out – wet with P1500 and P2000, then polish. How to check whether a scratch is too deep.

    P1500 → P2000

    Read · 2 min
  • Random orbital sander on a wing, sanding dust on the paint

    Car & paint

    Sanding and repairing rust bubbles on a car

    Open the bubble, remove the rust down to bare metal, feather the edge: P80 to P320 – then primer, primer surfacer, paint.

    P80 → P120 → P180 → P240 → P320

    Read · 1 min
  • Random orbital sander on a wing, sanding dust on the paint

    Car & paint

    Blending paint: keying the transitions properly

    Three zones, getting finer from the inside out: primer surfacer with P400, blend zone with P600 to P1000, clear coat transition with P1500 – so the edge stays invisible.

    P400 → P600 → P1000 → P1500

    Read · 1 min