Skip to content
KORNDEX – Home

Ultra-fine · Finish before polishing

Sandpaper P2000 P2000 grit (FEPA)

Before polishing. Before polishing, wet, with light pressure.

Roughly equivalent to 1000 Grit (US CAMI standard). Why the numbers differ

01 · Where it fits

Where P2000 sits in the sequence

Before

Pre-sand with P1500 – the jump to P2000 is no more than double, so the scratches disappear.

Ultra-fine range

P1200–P5000: Removing dust nibs, runs and paint defects, usually wet. Then polish – the scratches are so fine that the polish takes them out.

After

Carry on with P3000 until the surface is as fine as the next job needs.

P2000 in practice

Used on
Clear coat before polishing, motorcycle tanks, plastic for high gloss.
Tools
Foam sanding pad on a random orbital sander with 3 mm orbit, wet.
Typical mistake
Polishing straight over P1500 scratches: polishing takes forever and leaves holograms.
Tip from the workshop
Check the scratch pattern under a film of water: if the surface is an even satin matt without individual deeper scratches, it is ready to polish.

P2000 and P3000: what comes next

After P2000 comes either P3000 or polishing straight away. P3000 pays off on large areas and dark paint: the finer scratches polish out faster and with less heat. Even finer steps from P4000 are special abrasives for polishing preparation; for most repairs sanding ends after P2000 or P3000.

Fine grits: P1500, P2000, P3000 →

In the KORNDEX system:Finish · Remove paint defects P1200–P2000Finish · Before polishing P2000–P3000

What P2000 is used for

02 · Buy

Products in P2000

  • SOFT FINISH

    P2000KORNDEX
    Bestseller
    P400–P2000
    Grit
    150 mm
    Diameter
    10 pcs
    Contents
    €14.90

    €1.49 / pc · incl. VAT, plus shipping

  • PRO SHEET 230 × 280 wet

    P2000KORNDEX
    P400–P2000
    Grit
    230 × 280 mm
    Dimensions
    25 pcs
    Contents
    €19.90

    €0.80 / pc · incl. VAT, plus shipping

Sets with P2000

  • Finish set for high gloss

    KORNDEXFINISH SETKORNDEX
    P1000–P2000
    Grit
    30 discs, 25 sheets
    Contents
    €59.90

    incl. VAT, plus shipping

03 · Know-how

FAQs about P2000

What is P2000 sandpaper used for?

Before polishing: Before polishing, wet, with light pressure. Typical for Car & paint.

Is P2000 coarse or fine?

P2000 belongs to the ultra-fine range (P1200 to P5000): finish before polishing. The higher the number, the finer the grit.

Which grit comes after P2000?

After P2000 comes P2500 or – with the biggest jump allowed – P3000. Never more than double the number per step – that way the finer grit removes the scratches of the coarser one.

Should P2000 be used wet or dry?

On paint usually wet: from P800 the water cools, flushes away the swarf and makes the scratch pattern finer and more even. Use waterproof sheets or film discs for this – paper goes soft. P2000 also works dry with dust extraction, but clogs faster.

Which grit comes before P2000?

Before P2000, sand with P1500 (or finer). Jump straight to P2000 from too coarse a grit and you won't get the scratches out.

What do you sand P2000 with?

Foam sanding pad on a random orbital sander with 3 mm orbit, wet. Typical for: Clear coat before polishing, motorcycle tanks, plastic for high gloss.

What is the most common mistake with P2000?

Polishing straight over P1500 scratches: polishing takes forever and leaves holograms. Check the scratch pattern under a film of water: if the surface is an even satin matt without individual deeper scratches, it is ready to polish.

Related guides

  • Masked vehicle in the body shop

    Car & paint

    What grit for clear coat? Wet sanding P1500 to P3000

    Matting before a respray, removing dust nibs and runs, finishing before polishing – three jobs, three grit ranges.

    P1500 → P2000

    Read · 3 min
  • Fine sanding plastic by hand with a foam sanding pad

    Plastic & resin

    Restoring headlights: which grit?

    Wet sand from P800 to P2000, then polish – and seal afterwards, or the lens will be cloudy again after one summer.

    P800 → P1000 → P1500 → P2000

    Read · 1 min
  • Random orbital sander on a wing, sanding dust on the paint

    Plastic & resin

    Sanding and polishing epoxy resin

    River tables and castings: level coarse, then wet sand up to P2000 or P3000 and polish. Why the resin must be fully cured first.

    P120 → P180 → P240 → P320 → P400 → P600 → P800 → P1000 → P1500 → P2000

    Read · 1 min

Not sure P2000 is right?

The finder asks about material, machine and goal – and tells you the grit and product.

Start the abrasive finder →