Skip to content
KORNDEX – Home

Car & paint · 1 min read

Blending paint: keying the transitions properly

Three zones, getting finer from the inside out: primer surfacer with P400, blend zone with P600 to P1000, clear coat transition with P1500 – so the edge stays invisible.

Last updated: · published

KORNDEX sells abrasives – matching products are linked below the article.

Short answer: the grit sequence

Random orbital sander on a wing, sanding dust on the paint

Three zones, getting finer

In the middle, the repair: sand the primer surfacer smooth with P400. Around it, the blend zone where the base coat fades out thinly: evenly matt with P600 to P1000 or fine non-woven abrasive. Right at the outside, the zone that only gets clear coat: P1000 to P1500 or ultra-fine non-woven abrasive.

The further out, the finer – because that’s where there’s the least paint. Coarse scratches in the fade-out show through the thin base coat; with metallics, as light clouds or scratches in the transition.

To an edge, or a spot repair

Ideally let the clear coat run out to an edge or panel gap on the part – no edge will stand out there. A clear coat transition in the middle of a panel only works on small spots and needs blending thinner and polishing afterwards.

If the whole part is being clear coated, matt the entire surface outside the repair with P800 to P1000 or non-woven abrasive.

Checking before painting

The surface must be evenly matt everywhere. Shiny spots are places where the paint won’t adhere. Then degrease thoroughly, wipe with a tack cloth and paint.

FAQ

What do I use to get into swage lines and along edges?

Non-woven abrasive – it adapts to any shape and doesn’t sand through on edges as quickly as paper. Work wet or with matting paste until everything is evenly matt.

Which grit for the blend zone?

P600 to P1000 or a fine non-woven pad, evenly matt without shiny spots. Get finer towards the outer edge; where only clear coat lies, P1000 to P1500.

Terms in this article

All terms in the sanding glossary →

The whole sequence at once

4 grits, 1 × smallest pack each: PRO FILM 150 (10 pcs) P400 · P600 · P1000 · P1500.

Or as a set: Car paint starter set (P120–P600) for €69.90 →

incl. VAT, plus shipping

In the range

More on this topic

Matching products

  • KORNDEX

    PRO FILM 150

    Film-backed sanding disc Ø 150 mm – for the finest surfaces.

    €15.90

    €1.59 / pc · incl. VAT, plus shipping

  • KORNDEX

    SOFT FINISH

    Foam sanding pad Ø 150 mm – perfect results. Every time.

    €14.90

    €1.49 / pc · incl. VAT, plus shipping

  • KORNDEX

    PRO FLEECE

    Abrasive fleece 152 × 229 mm – matting, cleaning and scuffing without scratches.

    €14.90

    €1.49 / pc · incl. VAT, plus shipping

  • KORNDEX

    PRO SHEET 230 × 280 wet

    Waterproof sanding sheet 230 × 280 mm – for wet sanding paint.

    €19.90

    €0.80 / pc · incl. VAT, plus shipping

  • Random orbital sander on a wing, sanding dust on the paint

    Car & paint

    Masking before sanding and painting: protecting edges

    Masking tape for clean edges: where to mask, how to keep sanding dust and water out, and why you remove the tape promptly after painting.

    Read · 1 min
  • Feathering the edge between body filler and old paint by hand

    Car & paint

    Sanding a filler repair invisibly: feathering the edges

    Why filler repairs often still show through the paint – and how to sand them flat with P80, P120 and P180 to P240 and feather the edge out wide.

    P80 → P120 → P180 → P240

    Read · 1 min
  • Random orbital sander on grey primer surfacer on a masked car body

    Car & paint

    What grit before painting?

    Primer surfacer with P320 to P400, old paint with P400 to P600, plastic with P320 to P400 – depending on substrate and paint.

    P320 → P400 → P600

    Read · 2 min