Skip to content
KORNDEX – Home

Very fine · Keying paint

Sandpaper P800 P800 grit (FEPA)

Keying paint. Matting top coat, sanding between clear coats.

Roughly equivalent to 500 Grit (US CAMI standard). Why the numbers differ

01 · Where it fits

Where P800 sits in the sequence

Before

Pre-sand with P600 – the jump to P800 is no more than double, so the scratches disappear.

Very fine range

P500–P1000: Matting top coat and clear coat, preparing plastics for painting, sanding between coats.

After

Carry on with P1000 until the surface is as fine as the next job needs.

P800 in practice

Used on
Blend-in zone, clear coat between two coats, matting top coat.
Tools
Random orbital sander with 3 mm orbit or wet by hand with a sheet on a sanding block.
Typical mistake
Sanding dry without good extraction: P800 clogs quickly, the disc loses its cut and only polishes.
Tip from the workshop
When wet sanding, add a drop of washing-up liquid to the water – the sheet glides more evenly and does not clog.

P800 wet: matting clear coat

Sound old paint or clear coat that is only being recoated does not need removing, it needs to become evenly matt. P800 wet does that: the water flushes the swarf away and no glossy spots remain where the new paint would not adhere. Dry, that corresponds to roughly P400 to P600.

In the KORNDEX system:Paint preparation · Key paint & plastic P400–P1000

What P800 is used for

02 · Buy

Products in P800

  • PRO FILM 150

    P800KORNDEX
    Bestseller
    P240–P1500
    Grit
    150 mm
    Diameter
    10 pcs
    Contents
    €15.90

    €1.59 / pc · incl. VAT, plus shipping

  • SOFT FINISH

    P800KORNDEX
    Bestseller
    P400–P2000
    Grit
    150 mm
    Diameter
    10 pcs
    Contents
    €14.90

    €1.49 / pc · incl. VAT, plus shipping

  • PRO SHEET 230 × 280 wet

    P800KORNDEX
    P400–P2000
    Grit
    230 × 280 mm
    Dimensions
    25 pcs
    Contents
    €19.90

    €0.80 / pc · incl. VAT, plus shipping

03 · Know-how

FAQs about P800

What is P800 sandpaper used for?

Keying paint: Matting top coat, sanding between clear coats. Typical for Car & paint, Plastic.

Is P800 coarse or fine?

P800 belongs to the very fine range (P500 to P1000): keying paint. The higher the number, the finer the grit.

Which grit comes after P800?

After P800 comes P1000. Never more than double the number per step – that way the finer grit removes the scratches of the coarser one.

Should P800 be used wet or dry?

On paint usually wet: from P800 the water cools, flushes away the swarf and makes the scratch pattern finer and more even. Use waterproof sheets or film discs for this – paper goes soft. P800 also works dry with dust extraction, but clogs faster.

Which grit comes before P800?

Before P800, sand with P600 (or finer). Jump straight to P800 from too coarse a grit and you won't get the scratches out.

What do you sand P800 with?

Random orbital sander with 3 mm orbit or wet by hand with a sheet on a sanding block. Typical for: Blend-in zone, clear coat between two coats, matting top coat.

What is the most common mistake with P800?

Sanding dry without good extraction: P800 clogs quickly, the disc loses its cut and only polishes. When wet sanding, add a drop of washing-up liquid to the water – the sheet glides more evenly and does not clog.

Related guides

  • Fine sanding plastic by hand with a foam sanding pad

    Plastic & resin

    Restoring headlights: which grit?

    Wet sand from P800 to P2000, then polish – and seal afterwards, or the lens will be cloudy again after one summer.

    P800 → P1000 → P1500 → P2000

    Read · 1 min
  • Random orbital sander on a wing, sanding dust on the paint

    Plastic & resin

    Sanding and polishing epoxy resin

    River tables and castings: level coarse, then wet sand up to P2000 or P3000 and polish. Why the resin must be fully cured first.

    P120 → P180 → P240 → P320 → P400 → P600 → P800 → P1000 → P1500 → P2000

    Read · 1 min
  • Random orbital sander on grey primer surfacer on a masked car body

    Car & paint

    Preparing a motorcycle tank for painting

    Fill the dents, shape with P180 to P240, sand the primer surfacer with P400, key the old paint with P600 to P800. What to watch out for on a curved tank.

    P180 → P240 → P400 → P600 → P800

    Read · 2 min

Not sure P800 is right?

The finder asks about material, machine and goal – and tells you the grit and product.

Start the abrasive finder →