Skip to content
KORNDEX – Home

Car & paint · 1 min read

Sanding paint matt: scuffing with P800 to P1000

To repaint, scuff sound paint with P800 to P1000 wet or P400 to P600 dry until no gloss remains. How evenly matt looks and what can go wrong.

Last updated:

KORNDEX sells abrasives – matching products are linked below the article.

Short answer: the grit sequence

Random orbital sander smoothing the primed wing

Why you scuff paint

New paint adheres poorly to smooth, glossy paint. Scuffing creates fine scratches for the new paint to key into. It only removes the surface; it is not meant to remove paint.

Grit: wet fine, dry a bit coarser

Wet, P800 to P1000 are enough, the surface becomes evenly silky-matt. Dry, use P400 to P600 with dust extraction. What matters is that no gloss remains, not even in the corners.

Evenly matt: how to check

Against the light or with raking light you see glossy spots. Keep sanding there until the whole surface has the same degree of gloss. Then degrease and mask.

Typical mistakes

Only scuffed in spots: glossy islands make the paint come off there later.

Too coarse: P240 and coarser leave scratches that show in the new paint.

Sanded through: be careful on edges and creases, the paint is thinnest there.

FAQ

Which grit do I scuff paint with?

Wet with P800 to P1000, dry with P400 to P600, until the whole surface is evenly matt and no gloss remains.

Do I always have to scuff paint before repainting?

Yes: new paint adheres poorly to smooth, glossy paint. Scuffing creates the keying surface.

Terms in this article

All terms in the sanding glossary →

The whole sequence at once

4 grits, 1 × smallest pack each: PRO SHEET 230 × 280 wet (25 pcs) P400 · P600 · P800 · P1000.

Or as a set: Finish set for high gloss (P1000–P2000) for €59.90 →

incl. VAT, plus shipping

More on this topic

Matching products

  • KORNDEX

    PRO SHEET 230 × 280 wet

    Waterproof sanding sheet 230 × 280 mm – for wet sanding paint.

    €19.90

    €0.80 / pc · incl. VAT, plus shipping

  • KORNDEX

    SOFT FINISH

    Foam sanding pad Ø 150 mm – perfect results. Every time.

    €14.90

    €1.49 / pc · incl. VAT, plus shipping

  • KORNDEX

    PRO FLEECE

    Abrasive fleece 152 × 229 mm – matting, cleaning and scuffing without scratches.

    €14.90

    €1.49 / pc · incl. VAT, plus shipping

  • KORNDEXFINISH SETKORNDEX

    Finish set for high gloss

    For the finish before polishing – film, foam and wet sanding sheets.

    €59.90

    incl. VAT, plus shipping

  • KORNDEX

    Masking tape 110 °C

    Crepe tape for paintwork – leaves no residue, up to 110 °C, 50 m.

    €5.90

    €0.12 / m · incl. VAT, plus shipping

  • Random orbital sander on grey primer surfacer on a masked car body

    Car & paint

    What grit before painting?

    Primer surfacer with P320 to P400, old paint with P400 to P600, plastic with P320 to P400 – depending on substrate and paint.

    P320 → P400 → P600

    Read · 2 min
  • Random orbital sander on a wing, sanding dust on the paint

    Car & paint

    Blending paint: keying the transitions properly

    Three zones, getting finer from the inside out: primer surfacer with P400, blend zone with P600 to P1000, clear coat transition with P1500 – so the edge stays invisible.

    P400 → P600 → P1000 → P1500

    Read · 1 min
  • Fine sanding an oak board by hand with a sanding block

    Wood

    Sanding between coats: when, with what, which grit?

    P240 to P320 between coats of wood varnish, P320 to P400 for fine lacquers – only key the surface, do not sand through, and let it dry properly first.

    P240 → P320 → P400

    Read · 2 min