Car & paint · 4 min read
What grit sandpaper for car paint?
From body filler to finish: the grit sequence for a paint repair – and why you never skip a step.
Last updated: · published
KORNDEX sells abrasives – matching products are linked below the article.

The sequence is what matters
Car paint is not sanded with one grit but with a sequence. Each step removes the scratches of the one before; skip a step and you will see the coarse scratches through the clear coat later. Rule of thumb: never more than double the grit, so from P80 to P120 or P150, not to P240.
For a typical repair: P80 to shape the body filler, P120 and P180 to feather the edges, P240 before the primer surfacer. Smooth the primer surfacer with P320 and P400, and key the old paint with P400 to P600 so the new paint adheres.
Clear coat: paint defects and finish
Dust nibs and runs in the clear coat come out with P1500 to P2000, wet and with light pressure – first spot-sanded on the hand block, then level the whole area with P2000 on the soft foam pad (if you have P3000, it shortens polishing even further). Then polish: the scratches are so fine that the polish takes them out.
Which abrasive
For body filler and feathering, the paper disc (PRO CUT); for primer surfacer, the mesh disc (PRO NET) – it does not clog with dust. For top coat, clear coat and anything from P600 up, the film-backed disc (PRO FILM) or the foam pad (SOFT FINISH): flat backing, even scratch pattern, wet sanding too.
Machine, orbit and backing pad
For body filler and primer surfacer, a random orbital sander with around a 5 mm orbit and a hard or medium backing pad – it keeps the surface flat. From P400 and for clear coat, use a small orbit or the same machine at low speed with a soft interface pad, so the disc follows curves and does not sand through on edges.
Always use dust extraction: otherwise the dust between disc and paint rolls along and leaves pigtails that only show once you have painted.
The most common mistakes
Too much pressure: the disc barely spins freely any more, cuts pigtails and gets hot. The weight of the machine and a guiding hand are enough.
Running clogged discs for too long: they stop cutting and start polishing and smearing – and individual lumps drag scratches. Change them sooner rather than later.
Moving on without checking: before every step to a finer grit, apply guide coat and sand until it is gone everywhere. Whatever stays dark is a dent or a scratch from the previous grit.
Wet sanding car paint: which grit
Car paint is mostly wet sanded at the fine end: matting old paint with P800 to P1000, paint defects in the clear coat with P1500 to P2000. Primer surfacer and body filler stay dry – polyester filler soaks up water, and bare steel flash-rusts straight away.
Wrap the sheet around the hand block or the foam pad, keep surface and sheet wet, use light pressure. Wipe off the slurry now and then: shiny spots are low points that have not been reached yet. Rinse before every finer grit so no coarse grain travels along.
Sanding car paint before polishing
Before polishing, the sequence ends at P2000; if you have P3000, use it as the last step. What matters is an even scratch pattern without individual deeper scratches – the polish takes out fine scratches, but not a P1000 scratch that was missed.
Only sand fully cured paint. Mask edges and swage lines first: the paint is thinnest there, and that is where you break through first when polishing.
Which tools to sand car paint?
The random orbital sander with dust extraction for all surfaces – body filler, primer surfacer, old paint. The hand block for straight edges, swage lines and feathering filler edges. A non-woven pad for seams, door handle recesses and anywhere a block cannot reach. Plus guide coat, so you can see when a step is finished.
Sanding car paint with a random orbital sander
Put the sander on the surface, then switch it on; switch it off before lifting. Keep it flat – if the disc tilts, the edge of the pad cuts scratches and sands through on curves. Guide it in overlapping passes, with the weight of the machine.
On body filler and primer surfacer, higher speed with a hard or medium backing pad; on paint, lower speed and a soft interface pad. On edges and swage lines, take the sander away and carry on by hand.
FAQ
Can I skip steps in the grit sequence?
A jump of up to roughly double the grit is fine (P240 → P400). Bigger jumps leave scratches from the previous grit that you only see under the paint.
How many discs do I need for a bonnet?
Roughly two to three 150 mm discs per grit – fewer with dust extraction and abrasive mesh, more if the primer surfacer clogs them.
Terms in this article
- Deep scratches
- Clear coat
- Primer surfacer
- Scuff sanding (keying)
- Paint run (sag)
- Polishing
- Orbit (stroke)
- Speed
- Interface pad
- Dust extraction
- Swirl marks
- Guide coat (control powder)
- Matting
- Flash rust
- Scratch pattern
- Random orbital sander
- Abrasive fleece
The whole sequence at once
7 grits, 1 × smallest pack each: PRO CUT 150 (10 pcs) P80 · P120 · P180 · P240 · P320 · P400 · P600.
Or as a set: Car paint starter set (P120–P600) for €69.90 →
incl. VAT, plus shipping


