Skip to content
KORNDEX – Home

Metal · 1 min read

Sanding kerb damage on alloy wheels

Remove the burr with P120, feather the edges with P240, key with P400 before painting: this is how the rim edge gets smooth again – and when a wheel belongs in a specialist workshop.

Last updated: · published

KORNDEX sells abrasives – matching products are linked below the article.

Short answer: the grit sequence

Random orbital sander removing rust from a steel sheet

Check first, then sand

Surface scratches and scuffs on the rim flange can be sanded and painted. Cracks, deformation or deep gouges cannot: they affect the wheel’s strength – a wheel like that needs to be inspected by a specialist workshop.

The sequence

Mask off the tyre and surrounding area. Use P120 to remove the burr and raised material until the edge is round again. Use P180 and P240 to feather the transitions into the intact paint. Fill deeper spots with an aluminium-compatible body filler and sand back to P240.

Before primer and paint, key the whole repair area with P320 to P400, matt down the surrounding paint with a non-woven abrasive, then degrease.

Tips for aluminium

Aluminium is soft and clogs abrasives quickly – change the disc more often rather than pressing harder. For the curves of the rim flange, a foam pad or a soft interface pad works better than a hard backing pad. Prime bare aluminium promptly; it oxidises in air.

FAQ

Can I repair a diamond-cut wheel myself?

Only to a limited extent. The diamond-cut face is produced on a lathe – once sanded and painted, it looks different. Specialist wheel refurbishers handle these.

Terms in this article

All terms in the sanding glossary →

The whole sequence at once

5 grits, 1 × smallest pack each: PRO CUT 150 (10 pcs) P120 · P180 · P240 · P320, SOFT FINISH (10 pcs) P400.

incl. VAT, plus shipping

More on this topic

Matching products

  • KORNDEX

    PRO CUT 125

    Sanding disc Ø 125 mm – PRO CUT quality for compact random orbital sanders.

    €19.90

    €0.40 / pc · incl. VAT, plus shipping

  • KORNDEX

    PRO FLEECE

    Abrasive fleece 152 × 229 mm – matting, cleaning and scuffing without scratches.

    €14.90

    €1.49 / pc · incl. VAT, plus shipping

  • KORNDEX

    SOFT FINISH

    Foam sanding pad Ø 150 mm – perfect results. Every time.

    €14.90

    €1.49 / pc · incl. VAT, plus shipping

  • KORNDEX

    Masking tape 110 °C

    Crepe tape for paintwork – leaves no residue, up to 110 °C, 50 m.

    €5.90

    €0.12 / m · incl. VAT, plus shipping

  • Random orbital sander levelling the weld seam on a square tube

    Metal

    Keying before bonding: metal and plastic

    Adhesive holds on a rough, clean surface: P80 to P120 on metal, P180 to P240 on plastic – and why you degrease before and after sanding.

    P80 → P120 → P180 → P240

    Read · 1 min
  • Sanding sheet used by hand on a steel sheet

    Metal

    Sanding and polishing brass and copper

    Soft non-ferrous metals: patina with non-woven abrasive, scratches off with P240, then wet up to P2000 and polish – and why you seal it afterwards.

    P240 → P400 → P600 → P1000 → P1500 → P2000

    Read · 1 min
  • Random orbital sander on a wing, sanding dust on the paint

    Car & paint

    Sanding and repairing rust bubbles on a car

    Open the bubble, remove the rust down to bare metal, feather the edge: P80 to P320 – then primer, primer surfacer, paint.

    P80 → P120 → P180 → P240 → P320

    Read · 1 min