Skip to content
KORNDEX – Home

Metal · 1 min read

Sanding a bicycle frame for new paint

Remove old paint and rust with P120 to P180, smooth with P240 to P320 and degrease before priming. Tubes and lugs by hand, with little pressure.

Last updated:

KORNDEX sells abrasives – matching products are linked below the article.

Short answer: the grit sequence

Random orbital sander levelling the weld seam on a square tube

Preparing the frame

Remove all parts, tape or plug bearings and threads and clean and degrease the frame thoroughly. Only a clean, dry frame is painted. Do not sand carbon frames – the fibres must not be damaged.

Removing: P120 to P180

Remove old paint and rust with P120, P80 on stubborn spots, then smooth the coarser marks with P180. Steel should be sanded to bare metal where rust sits; aluminium needs its own abrasives so no steel residue stays in the metal.

Tubes and lugs by hand

Curves, lugs and edges are sanded with a strip of sandpaper or sanding fleece in the hand, not with the machine: that keeps the shape and you do not sand through. Little pressure, along the length of the tubes.

Smoothing and priming

Refine the scratch pattern with P240 to P320 until no deep marks are visible. Then remove dust, degrease and prime immediately so bare metal does not tarnish or rust again.

FAQ

Which grit for a bicycle frame?

P120 to P180 to remove paint and rust, then P240 to P320 to smooth before priming.

Can I sand a carbon frame?

No – do not damage the fibres on a carbon frame. Only treat the paint layer following the carbon guide.

Terms in this article

All terms in the sanding glossary →

The whole sequence at once

4 grits, 1 × smallest pack each: PRO CUT 150 (10 pcs) P120 · P180 · P240 · P320.

incl. VAT, plus shipping

More on this topic

Matching products

  • KORNDEX

    PRO CUT 150

    Professional sanding disc Ø 150 mm – maximum stock removal.

    €24.90

    €0.50 / pc · incl. VAT, plus shipping

  • KORNDEX

    PRO FLEECE

    Abrasive fleece 152 × 229 mm – matting, cleaning and scuffing without scratches.

    €14.90

    €1.49 / pc · incl. VAT, plus shipping

  • KORNDEX

    PRO STRIP 70 × 420

    Sanding strips 70 × 420 mm with hook and loop – for hand blocks and orbital sanders.

    €22.90

    €0.92 / pc · incl. VAT, plus shipping

  • KORNDEX

    Hand sanding block 70 × 198

    Hand sanding block with hook and loop and extraction port – for strips and rolls.

    €14.90

    incl. VAT, plus shipping

  • KORNDEX

    FFP2 dust mask

    Fold-flat FFP2 mask with valve – 10 pcs.

    €12.90

    incl. VAT, plus shipping

  • Random orbital sander levelling the weld seam on a square tube

    Metal

    Sanding stainless steel and aluminium

    Soft and stainless metals sand differently from mild steel: aluminium clogs, stainless steel discolours. The sequence that gives you an even scratch pattern.

    P80 → P120 → P180 → P240 → P320 → P400

    Read · 2 min
  • Sanding sheet used by hand on a steel sheet

    Metal

    Sanding and polishing brass and copper

    Soft non-ferrous metals: patina with non-woven abrasive, scratches off with P240, then wet up to P2000 and polish – and why you seal it afterwards.

    P240 → P400 → P600 → P1000 → P1500 → P2000

    Read · 1 min
  • Random orbital sander removing rust from a steel sheet

    Metal

    Sanding kerb damage on alloy wheels

    Remove the burr with P120, feather the edges with P240, key with P400 before painting: this is how the rim edge gets smooth again – and when a wheel belongs in a specialist workshop.

    P120 → P180 → P240 → P320 → P400

    Read · 1 min