Skip to content
KORNDEX – Home

Abrasives · 2 min read

125 mm sanding discs: grit, hole pattern, hook and loop

What the small disc is good for, which grit for which job, how to count the hole pattern on your pad – and why hook and loop and diameter have to match exactly.

Last updated:

KORNDEX sells abrasives – matching products are linked below the article.

Random orbital sander on the door of a black car

When 125 mm is the right size

125 mm is the size of the small, light random orbital sanders: they sit well in one hand, get closer to edges and inside corners and can be used for a long time overhead or on vertical surfaces. Typical jobs are furniture, doors, window frames, small filler spots and car repairs where only part of a panel is painted.

On large, flat surfaces the 150 mm disc is faster: it covers more with every pass, and the larger pad keeps the surface flatter. If you sand a lot of area, take 150 mm; if you have a lot of detail, you will be done sooner with 125 mm.

Which grit on the 125 mm disc

The grit depends on the job, not on the diameter. Coarse for stock removal: P60 to P80 for old paint, saw marks and shaping body filler. Medium for smoothing: P120 to P180 for wood and for feathering filler edges. Fine before the finish: P240 before varnish, P320 to P400 for primer surfacer and for keying old paint.

As with every sequence: never more than double the grit per step, so P80 to P120 and not to P240. Otherwise scratches from the coarse step stay behind, and you only see them under the paint.

Hole pattern: count the holes on your pad

An 8-hole pattern is common on 125 mm, but other pads exist too. Before you buy discs, turn the sander over and count the extraction holes in the pad. If the holes in disc and pad do not line up, the sander barely extracts: the dust stays under the disc, it clogs and leaves pigtails.

Multi-hole discs with many small holes fit several hole patterns, and mesh discs extract across the whole surface on any pad. The article on hole patterns goes into the details.

Hook and loop: disc and pad have to match

The disc has to be exactly the size of the pad. One that is too large overhangs, flaps and tears at the edge; one that is too small leaves a ring of hook material exposed, which rubs along, wears and drags scratches. Put the disc on centred, line up the holes, press it on firmly for a moment.

If new discs still fall off, the hook surface of the pad is usually worn. An interface pad between pad and disc protects it and makes the cut softer – good for curves and profiles.

Small sander, same technique

The small random orbital sander also sands with its own weight. Do not push down, guide it in overlapping passes, switch it on on the surface and off before lifting. With dust extraction the disc lasts longer and the surface stays free of pigtails.

FAQ

Does a 125 mm disc fit a 150 mm pad?

No. A ring of hook material stays exposed on the outside, rubs along, gets hot and wears. Disc and pad must have the same diameter.

Which grit do I start with on wood?

On raw, planed wood with P80 or P120, on old paint with P80. Then P120 and P180, and finally P240 before varnish.

Do I need a different backing pad for 125 mm?

The pad belongs to the sander: a 125 mm sander has a 125 mm pad. Replace it with one of the same diameter, the same thread and the same hole pattern.

Terms in this article

All terms in the sanding glossary →

In the range

More on this topic

Matching products

  • KORNDEX

    PRO CUT 125

    Sanding disc Ø 125 mm – PRO CUT quality for compact random orbital sanders.

    €19.90

    €0.40 / pc · incl. VAT, plus shipping

  • KORNDEX

    Soft interface pad

    Soft interface pad Ø 125 or 150 mm – for contours and for mesh discs.

    €8.90

    incl. VAT, plus shipping